Reference

Here is a list of all modules:

[detail level 123]

Firmware configuration	CMSIS-DAP is designed for debug units with a Cortex-M microcontroller
Debug Unit Processor	CMSIS-DAP firmware runs on debug units with a Cortex-M microcontroller
Configure I/O ports and debug unit	DAP_config.h configures I/O ports and debug unit hardware parameters
CMSIS-DAP Debug Unit Information	Provides definitions about the hardware and configuration of the Debug Unit
CMSIS-DAP Hardware I/O Pin Access	Standard I/O Pins of the CMSIS-DAP Hardware Debug Port support standard JTAG mode and Serial Wire Debug (SWD) mode
CMSIS-DAP Hardware Status LEDs	CMSIS-DAP Hardware may provide LEDs that indicate the status of the CMSIS-DAP Debug Unit
CMSIS-DAP Timestamp	Access function for Test Domain Timer
CMSIS-DAP Initialization	CMSIS-DAP Hardware I/O and LED Pins are initialized with the function DAP_SETUP
Configure USB peripheral	CMSIS-DAP firmware communicates via USB with the host computer
Flash program the firmware	The CMSIS-DAP firmware is programmed into the Flash ROM of a debug unit
Connect SWO trace	Optionally, you may add a CMSIS-Driver USART to interface to SWO
Connect UART communication port	Optionally, you may add a CMSIS-Driver USART to interface to UART communication port
Validate the debug unit operation	A CMSIS-DAP conforming debug unit must be validated
CMSIS-DAP Commands	Commands between Debug Unit and host computer
General Commands	Information and Control commands for the CMSIS-DAP Debug Unit
DAP_Info	Get Information about CMSIS-DAP Debug Unit
DAP_HostStatus	Sent status information of the debugger to Debug Unit
DAP_Connect	Connect to Device and selected DAP mode
DAP_Disconnect	Disconnect from active Debug Port
DAP_WriteABORT	Write ABORT Register
DAP_Delay	Wait for specified delay
DAP_ResetTarget	Reset Target with Device specific sequence
Common SWD/JTAG Commands	Set SWD/JTAG clock and control/monitor SWD/JTAG I/O pins
DAP_SWJ_Pins	Control and monitor SWD/JTAG Pins
DAP_SWJ_Clock	Select SWD/JTAG Clock
DAP_SWJ_Sequence	Generate SWJ sequence SWDIO/TMS @SWCLK/TCK
SWD Commands	Configure the parameters for SWD mode
DAP_SWD_Configure	Configure SWD Protocol
DAP_SWD_Sequence	Generate SWD sequence and output on SWDIO or capture input from SWDIO data
SWO Commands	Configure the parameters for SWO mode
DAP_SWO_Transport	Set SWO transport mode
DAP_SWO_Mode	Set SWO capture mode
DAP_SWO_Baudrate	Set SWO baudrate
DAP_SWO_Control	Control SWO trace data capture
DAP_SWO_Status	Read SWO trace status
DAP_SWO_ExtendedStatus	Read SWO trace extended status
DAP_SWO_Data	Read SWO trace data
JTAG Commands	Detect and configure the JTAG device chain
DAP_JTAG_Sequence	Generate JTAG sequence TMS, TDI and capture TDO
DAP_JTAG_Configure	Configure JTAG Chain
DAP_JTAG_IDCODE	Read JTAG IDCODE
Transfer Commands	Read and Writes to CoreSight registers
DAP_TransferConfigure	Configure Transfers
DAP_Transfer	Read/write single and multiple registers
DAP_TransferBlock	Read/Write a block of data from/to a single register
DAP_TransferAbort	Abort current Transfer
Atomic Commands	Execute atomic commands
DAP_ExecuteCommands	Execute multiple DAP commands from a single packet
DAP_QueueCommands	Queue multiple DAP commands provided in a multiple packets
UART COM Commands	Target communication via extra UART
DAP_UART_Transport	Set UART transport mode
DAP_UART_Configure	Set UART configuration
DAP_UART_Control	Control UART data receive and transmit
DAP_UART_Status	Get UART status
DAP_UART_Transfer	Transfer data via UART
Response Status	Status Information in Response Data
CMSIS-DAP Vendor Commands	Extend CMSIS-DAP firmware with commands